You are viewing: Tank Heaters, Fittings, Sewer Hatches etc.

Water Heater Exterior Flange Seal Kit
Enlarge Photo		Description: This installation kit contains everything you need to seal the exterior flange or door kit of your new or existing water heater. This kit contains 72" of our premium butyl tape, which is perfect for both aluminum and fiberglass siding. It also contains 32 #8 x 1" hex screws for a professional installation.		Part Number: 04215 - Flange Seal Kit, pkg.

Drain Hose Wrench
Enlarge Photo		Description: Specially designed to help with removal of 3" sewer hose and caps. Made of durable plastic for long life and trouble free usage. Simply place the wrench on the cap or termination fitting and turn in the proper direction. No more stuck fittings to deal with. A great tool for every RV'er.		Part Number: 04154 - Drain Hose Wrench, pkg.

Blow Out Plug
Enlarge Photo		Description: Used to apply air pressure to your water lines to insure that all of the water is removed before winterizing. With less water remaining in the lines, your anti-freeze will work at the dilution you want. Also helps with the removal of anti-freeze when dewinterizing.		Part Number: 03054 - Blow Out Plug, pkg.

Dual Barbed Drain Cock
Enlarge Photo		Description: Durable plastic valve is designed for multiple uses and built to last. The dual size barbed fittings make choosing the right size a snap and the 2" mounting flange helps provide a good seal. The valve will replace most OEM fresh water tank drain valves as well as those mounted on the exterior walls of the RV or boat.		Part Number: 03182 - 3/8" - 1/2" Dual Barbed Drain Cock, pkg.

Holding Tank Heater
Enlarge Photo		Description: This holding tank heating element is an easy and practical way to winterize your RV or trailer‘s tanks. It can be used on either fresh or septic tanks. It is dual voltage ready for both 12-volt and 110-volt applications. These elements are thermostatically controlled and activate at approximately 34 degrees Fahrenheit to stop the contents of your tank from freezing. The element is 30" x 13" and is a foil covered heater. It comes with a 24" ground wire for safety, 6‘ of 120-volt wiring for easy installation. Each heater draws approximately 1-Amp AC and 10-Amps DC current when in use. Multiple elements can be used where needed for tank coverage.		Part Number: HTH-A Holding Tank Header Click below for product specs. Click Here for Product Table

Hatch Installation Kit
Enlarge Photo		Description: Includes everything you need to replace an existing hatch or install a new one: new screws and enough of our premium butyl tape to properly seal your hatches.		Part Number: 04195 - Hatch Installation Kit, pkg. (includes 36" butyl tape & 10 white screws)

Tags
Enlarge Photo		Description: Replacement for any missing or faded tags on your RV. Identifies hatch for easy location.		Part Number: 00010 - ID Tag For Water Access Hatch 00080 - ID Tag For Sewer Hose Hatch 00090 - ID Tag For Auxiliary Shower

Vacuum Breaker/Check Valve
Enlarge Photo		Description: Installed between the water hose connection and the tank flusher itself, this item protects harmful bacteria and waste from entering the hose or water supply system. Meets IAPMO standards and is required for tank flush equipment on all OEM installations. ASSE 1001-02 requires that it be installed 6" or more above the highest point of any item connected to the waste tank that the flusher is installed in.		Part Number: 571-Vac-Chk-A - Vacuum Breaker/Check Valve, pkg.

Sprayer
Enlarge Photo		Description: "Glued In" version of the tank sprayer. Designed to provide a high pressure multi-directional water stream into the holding tank to help remove solids, paper, or sludge from within the tank. Must be installed no lower than 2" from the top of the tank to meet IAPMO and Canadian certification.		Part Number: 571-Sprayer-A - Sprayer, pkg.

Water Inlet
Enlarge Photo		Description: Our Flusher water inlet provides the water to the flusher sprayer from an exterior mounted location. The plastic water inlet reduces corrosion associated with tank flusher operations and can be replaced easily if needed. The inlet does not have a back flow breaker per the IAPMO code for better water movement and less possibility of blockage.		Part Number: 160-85-A-2PZ-A - Water Inlet, Plastic, pkg. 160-85-A-2Z-A - Water Inlet, Brass, pkg.

Sewer Hose/Storage Hatch
Enlarge Photo		Description: This sewer/storage hatch is designed with convenience in mind. Back plate is constructed to accept a 4" rigid PVC or flexible hose to create a storage area for your sewer hoses or other items. When used with our Cap #237G, this hatch can be mounted both above or below the floor and still achieve a totally contained storage system. Made of a durable plastic that won‘t fade or discolor. Paintable with no preparation needed to match any RV exterior. (PVC pipe not included)		Part Number: L8182-A - Key Lock, Polar White, pkg. L8D82-A - Thumb Lock, Polar White, pkg. L8D83-A - Thumb Lock, Black, pkg. 237G - Cap for 4" PVC Pipe, bulk Dimensions: Cut Out Dim. 4-3/4" x 5-7/8" Outside Dim. 6-1/2" x 7-5/8"

Horse Shoe Vent
Enlarge Photo		Description: Made of durable, long lasting plastic that won't fade or discolor. Perfect for replacing existing vents or to install a side exit vent.		Part Number: 298-01-A-PW-A - Horse Shoe Vent, Polar White, pkg.

Flush Slip Fitting
Enlarge Photo		Description: Flush fittings will bond directly to the surface of the tank.		Part Number: 217 - 2" Flush Slip Fitting, bulk 217-A - 2" Flush Slip Fitting, pkg. 221 - 1-1/2" Flush Slip Fitting, bulk 221-A - 1-1/2" Flush Slip Fitting, pkg.

Projected Male Spigot
Enlarge Photo		Description: Projected fittings have a small protrusion that will fit into the hole in the tank for added strength.		Part Number: 216-A-MS - 3" Projected Male Spigot, bulk 216-A-MS-A - 3" Projected Male Spigot, pkg.

Flush Treaded Fitting
Enlarge Photo		Description: These ABS fittings are perfect for replacement tanks or to replace damaged fittings. Made of high strength ABS for durability and easy installation using ABS cement.		Part Number: 220-90-B - 1-1/2" Flush Threaded Fitting, bulk 220-90-B-A - 1-1/2" Flush Threaded Fitting, pkg. 220-90-A - 2" Flush Threaded Fitting, bulk 220-90-A-A - 2" Flush Threaded Fitting, pkg. 220-B-76 - 3" Flush Threaded Fitting, bulk 220-B-76-A - 3" Flush Threaded Fitting, pkg.

Projected Slip Fitting
Enlarge Photo		Description: Projected fittings have a small protrusion that will fit into the hole in the tank for added strength.		Part Number: 160-75-H - 1-1/2" Projected Slip Fitting, bulk 160-75-H-A - 1-1/2" Projected Slip Fitting, pkg. 160-77-A - 2" Projected Slip Fitting, bulk 160-77-A-A - 2" Projected Slip Fitting, pkg. 216-SF - 3" Projected Slip Fitting, bulk 216-SF-A - 3" Projected Slip Fitting, pkg. 220-A-76 - 3" Projected Threaded Fitting, bulk 220-A-76-A - 3" Projected Threaded Fitting, pkg.